Keysight N5227B Скачать руководство пользователя страница 342

Страница: 342 / 415

7-24 Keysight N5227B Service Guide

Repair and Replacement Procedures
Removing and Replacing the A20 Power Supply Assembly

Removing and Replacing the A20 Power Supply Assembly

Tools Required

— T-10 TORX driver (torque to 9 in-lb or 1.02 N.m)
— T-20 TORX driver (torque to 21 in-lb or 2.38 N.m)
— ESD grounding wrist strap

Removal Procedure

Refer to

Figure 7-11

for this procedure.

Disconnect the power cord.

Remove the outer and inner covers. Refer to

“Removing the Covers” on

page 7-6

Remove the three flat head screws (item

①

) from the power supply

bracket.

Remove the seven pan head screws (item

➁

) from the power supply rear

panel.

Slide the A20 power supply assembly out the rear of the analyzer.

Replacement Procedure

Reverse the order of the removal procedure.

Perform the post-repair adjustments, verifications, and performance tests

that pertain to this removal procedure. Refer to

Table 7-2 on page 7-74

IMPORTANT!

If the rear power supply rear cover must be replaced, a new

KC label is required (part number N5240-80041). Refer to

“Keysight

Support, Services, and Assistance” on page 6

Содержание N5227B
































































































































































































































































































































































































































Результаты поиска

Содержание N5227B

Отзывы:

Похожие инструкции для N5227B

Бренды по названию

Популярные бренды

Keysight N5227B, Руководство по обслуживанию

Результаты поиска

Содержание N5227B

Отзывы:

Похожие инструкции для N5227B

Бренды по названию

Популярные бренды