Keysight N4372E Скачать руководство пользователя страница 51

Страница: 51 / 152

Keysight N4372E Lightwave Component Analyzer User’s Guide

Making Measurements

• For additional information, please refer to "Optimize a measurement"

and "Calibrate a measurement" in the documentation of the network

analyzer.

Electrical calibration for single-ended measurements

To ensure the specified performance of the LCA, you need to perform a full

two-port electrical calibration.

Calibrate before you start using the Lightwave Component Analyzer

application. Alternatively, return to EE measurement mode, as described in

Returning to Electrical Measurements

on page 69, to calibrate. For

calibrating the Lightwave Component Analyzer using calibration kit, follow

these steps:
1 Set your measurement parameters.
2 From the “Calibration” menu, select “Other Cals” -> “Smart Cal”.
3 Select "2 Port Cal".
4 On two-port network analyzers, select port 2 as "selected 2nd port".

On 4-port network analyzers, select port 4 as "selected 2nd port". If

you plan to use other ports for your measurements, select them for the

calibration and later in the LCA software port configuration window.

For more information, refer to

Selecting Port Configuration

on page 83.

5 Follow the instruction for further steps shown on the Network

Analyzer.

6 After the calibration has been completed, save the calibration file.

NOTE

When in EO measurement mode, you need to return to EE measurement

mode first before you can perform an electrical calibration.

NOTE

It is recommended to use the 6 mm and 14 mm torque wrenches

(Keysight part number 8710-2812 and 8710-2813, 45 N-cm/4 lb-in)

and a 12mm wrench to tighten all RF connections during the calibration.

Содержание N4372E

























































































































































Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды

Keysight N4372E, Руководство пользователя

Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды