Keysight N2820A Скачать руководство пользователя страница 15

Страница: 15 / 110

General Information

Safety Information

N2820/1A User’s Guide

Safety Information

This manual provides information and warnings essential for

operating this probe in a safe manner and for maintaining it in safe

operating condition. Before using this equipment and to ensure

safe operation and to obtain maximum performance from the

probe, carefully read and observe the following warnings, cautions,

and notes.
This product has been designed and tested in accordance with

accepted industry standards, and has been supplied in a safe

condition. The documentation contains information and warnings

that must be followed by the user to ensure safe operation and to

maintain the product in a safe condition.
Note the external markings on the probe that are described in this

document.
To avoid personal injury and to prevent fire or damage to this

product or products connected to it, review and comply with the

following safety precautions. Be aware that if you use this probe

assembly in a manner not specified, the protection this product

provides may be impaired.

WARNING

Use Only Grounded Instruments.
Do not connect the probe’s ground lead to a potential other than earth

ground. Always make sure the probe and the oscilloscope are grounded

properly.

WARNING

Connect and Disconnect Properly.
Connect the probe to the oscilloscope and connect the ground lead to

earth ground before connecting the probe to the circuit under test.

Disconnect the probe input and the probe ground lead from the circuit

under test before disconnecting the probe from the oscilloscope.

Содержание N2820A















































































































Результаты поиска

Содержание N2820A

Отзывы:

Бренды по названию

Популярные бренды

Keysight N2820A, Руководство пользователя

Результаты поиска

Содержание N2820A

Отзывы:

Бренды по названию

Популярные бренды