Keysight M9502A Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 142

background image

100

Keysight M9502A/M9505A AXIe Chassis User Guide

For Module Developers

Chassis Backplane Connections

Chassis Backplane Connections

M9502A Backplane

The photo below reveals the M9502A backplane, with modules removed from all
slots. The backplane provides Zone 2 connectors P20, P21, P23, P24 and Zone 1
connector J10. Connector designations are shown for instrument slot 1.

The backplane differs from the M9505A in that the 2-slot backplane does not
utilize P22

(see

“M9505A Backplane”

A typical module layout is shown below the backplane photo, with the mating
connectors J20 through J24 and P10.

Depending on module type, you may implement all or none of J20-J24 for use in
the 2-slot chassis. You will always need connector P10 to power the module.
Optionally, you may need connector:

-

J20 to use the timing and trigger buses

-

J23 to use the base fabric (channel 1) and data fabric (channels 1 and/or 2)
interfaces

-

J23 and J20 to use up to 22 local bus interface pairs

-

J24 to expand local bus use to 42 pairs

-

J24 and J21 to expand local bus use to 62 pairs

-

J22 if the module is to be used as an instrument hub for the M9505A

Logical Slot 2

ESM Slot

Logical Slot 1

Instrument Slot 2

Logical Slot 3

Zone 2

Zone 1

AXIe Module Rear (mating) Edge

Instrument Slot 1 (Hub Slot)

«
...
108
109
110
111
112
...
»

Содержание M9502A















































































































































Отзывы:

Нет отзывов

Похожие инструкции для M9502A

Бренд: HPE Страницы: 5

Бренд: Contec Страницы: 28

Supero SC933E1-R760B

Бренд: Supermicro Страницы: 84

Supero SC933 Series

Бренд: Supermicro Страницы: 84

Бренд: Lumens Страницы: 2

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 114

PXI Express PXIe-1082

Бренд: NI Страницы: 67

Isilon IQ 32000X-SSD

Бренд: Isilon Systems Страницы: 40

PowerEdge MX740c

Бренд: Dell EMC Страницы: 43

PowerEdge MX5000s

Бренд: Dell EMC Страницы: 43

Бренд: Dell EMC Страницы: 56

PowerEdge MX Series

Бренд: Dell EMC Страницы: 75

PowerEdge MX7000

Бренд: Dell EMC Страницы: 83

PowerEdge MX740c

Бренд: Dell EMC Страницы: 136

PowerEdge MX840c

Бренд: Dell EMC Страницы: 144

PXI Express NI PXIe-1065

Бренд: National Instruments Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды