Keysight InfiniiVision M9241A Скачать руководство пользователя страница 12

Страница: 12 / 72

Keysight M9241/42/43A PXIe Oscilloscopes and M9240A AutoProbe Power Module Startup Guide

Unpack and Inspect the Module

Inspect for Damage

After unpacking an instrument, inspect it for any shipping damage. Report any

damage to the shipping agent immediately, as such damage is not covered by the

warranty.

Return an Instrument for Service

Should it become necessary to return an instrument for repair or service, follow

the steps below:

WARNING

DO NOT use these techniques for a static-safe work station when working on

circuitry with a voltage potential greater than 500 volts.

CAUTION

To avoid damage when handling a module, do not touch exposed connector pins.

NOTE

It is recommended that you return all modules and cables of the M924xA instrument for repair

and calibration.

Содержание InfiniiVision M9241A









































































Результаты поиска

Содержание InfiniiVision M9241A

Отзывы:

Похожие инструкции для InfiniiVision M9241A

Бренды по названию

Популярные бренды

Keysight InfiniiVision M9241A, Руководство для стартапов

Результаты поиска

Содержание InfiniiVision M9241A

Отзывы:

Похожие инструкции для InfiniiVision M9241A

Бренды по названию

Популярные бренды