manualshive.com logo in svg

Keysight Infiniium 8000 Series, Руководство по обслуживанию

Поделиться
Скачать
Keysight Infiniium 8000 Series Скачать руководство пользователя страница 81

                                          Chapter 5: Troubleshooting

To check the backlight inverter voltages

81

To check the backlight inverter voltages

The backlight inverter board A5 is located in the front- left corner of the oscilloscope 
(as you face the front panel). 

• There is an input connector at one side of the board. 

• There are two output connectors on the other end of the board, that power the two 

backlights which are inserted into the flat panel display. 

The output voltage is approximately 300- 450 V

rms

, 40 kHz (measured differentially 

between the two wires) when the backlight is illuminated. The voltage is approximately 
1 kV before the backlight tube is illuminated. A red LED on the backlight inverter board 
illuminates when the output voltage is present.

When the backlight goes off (when the oscilloscope’s operating system switches to screen 
saver mode) the voltage on pins 1 and 2 (with respect to ground) slowly decays to 0 V.

The outputs are controlled by the input. Notice that input pin 5 goes low to enable the 
output voltage. These pins can be reached at J1 on the display board A11 on systems 
that use the Intel motherboard, or on connector CN10 on systems that use the ADLINK 
motherboard. 

Table 5-5 

Backlight Inverter Board Input Voltages

Input  Pin  #

7

6

5

4

3

2

1

Backlight OFF

0 V

0 V

0 V

0 V

0 V

0 V

0 V

Backlight ON

5 V

0 V

2.5 V

0 V

0 V

12 V

12 V

Содержание Infiniium 8000 Series



































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды