Keysight Infiniium 8000 Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 162

background image

Chapter 2: Preparing for Use
To connect the mouse, keyboard, LAN, printer, and GPIB cable

24

To connect the mouse, keyboard, LAN, printer, and GPIB cable

Mouse. Plug the mouse into the mouse connector on the back panel of the oscilloscope.

Keyboard. Plug the keyboard cable into the keyboard connector on the back panel of the

oscilloscope.

LAN Cable. Connect your LAN cable to the RJ- 45 connector on the back panel of the oscilloscope.

Printer Cable. If you have a USB printer, you will need to connect its cable to one of the four USB

ports on the rear panel, or to the USB port on the front panel.

If you have a parallel printer, you will need to connect its parallel printer cable to the
Parallel Printer connector on the oscilloscope.

GPIB Cable. If you will be controlling the oscilloscope through the GPIB, attach your GPIB cable to

the GPIB connector on the rear of the oscilloscope.

Figure 2-4

Back Panel

Note:

Your instrument’s rear panel configuration may differ from this diagram. Connect the cables based on your
instrument’s configuration.

While you can operate many oscilloscope functions using only the front-panel keys and
knobs, you will need the mouse to access advanced oscilloscope functions through the
graphical interface, or to find out more about the oscilloscope through the built-in
information system.

A keyboard must be plugged into the oscilloscope before the Windows operating system
has started booting.

Depending on your building’s LAN configuration, you may need to set up the oscilloscope’s
network configuration after connecting the LAN cable to the oscilloscope. If your
building’s network uses DHCP, many parameters will already be compatible. Before you
set up the network configuration, you should exit the oscilloscope application. If you do
not know how to setup the network, see your network administrator or use the Windows
XP on-line help.

Mouse

Keyboard

USB
Ports

GPIB

LAN

Parallel
Printer

Line In
Line Out
Microphone

«
...
22
23
24
25
26
...
»

Содержание Infiniium 8000 Series



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Infiniium 8000 Series

SACE Tmax XT Series

Бренд: ABB Страницы: 11

D-IMager EKL3104

Бренд: Panasonic Страницы: 13

Бренд: Labokey Страницы: 5

Бренд: E-Z Trail Страницы: 8

Бренд: B&K Страницы: 10

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: Fayat Group Страницы: 50

Бренд: Halyard Страницы: 88

Бренд: HABYS Страницы: 16

ENET-232 Series

Бренд: National Instruments Страницы: 105

Бренд: Yamaha Страницы: 126

DM 2000 Version 2

Бренд: Yamaha Страницы: 8

Бренд: Feniex Страницы: 5

VIMCO Sivoia SV-CCI-GRP

Бренд: Lutron Electronics Страницы: 2

Бренд: GE Страницы: 2

Бренд: Kelvin Страницы: 30

Pro hunter 2525

Бренд: SprotDog Страницы: 28

Бренд: Barikell Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды