Keysight E8663D Скачать руководство пользователя страница 339

Страница: 339 / 358

Keysight E8357D/67D & E8663D PSG User’s Guide 325

Troubleshooting

Signal Generator Locks Up

If the signal generator is locked up, check the following:

— Make sure that the signal generator is not in remote mode (in remote mode,

the

annunciator appears on the display). To exit remote mode and unlock

the front panel keypad, press

Local

— Make sure that the signal generator is not in local lockout condition. Local

lockout prevents front panel operation. For more information on local

lockout, refer to the

Keysight Signal Generators Programming Guide

— Check for a progress bar on the signal generator display, which indicates

that an operation is in progress.

— Press

Preset

— Cycle power on the signal generator.

Fail–Safe Recovery Sequence

Use the fail–safe recovery sequence only if the previous suggestions do not

resolve the problem.

CAUTION

This process does reset the signal generator, but it also destroys the following

types of data:

— all user files (instrument state and data files)

— DCFM/DC

M calibration data

— persistent states

NOTE

Do not attempt to perform any other front panel or remote operations during

the fail–safe sequence.

To run the fail–safe sequence, follow these steps:

Hold down the

Preset

key while cycling power.

Continue to hold down the

Preset

key until the following message is

displayed:

WARNING

You are entering the diagnostics menu which can cause unpredictable

instrument behavior. Are you sure you want to continue?

Содержание E8663D







































































































































































































































































































































































Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды

Keysight E8663D, Руководство пользователя

Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды