Keysight E6650A EXF Скачать руководство пользователя страница 648 | Manualshive

Страница: 648 / 657

background image

6 List Sequence Measurements
View/Display

View/Display

The View/Display key opensthe Display Menu (common to most measurements) and the View menu for
the current measurement.

Only two views are available for the List Sequencer measurement: the Results Metric View, and the RF
envelope view. The RF envelope view is only available when basic IQ data is captured in Sequence
Analyzer mode.

parameter_table_23.52941

52.94118

Key Path

Front-panel key

Initial S/W Revision

A.05.00

Help Map ID

3439

Display

The Display menu is common to most measurements, and is used for configuring items on the display.
Some Display menu settings apply to all the measurements in a mode, and some only to the current
measurement. Those under the System Display Settings key apply to all measurements in all modes.

Key Path

Display

Key Path

View/Display

Initial S/W Revision

Prior to A.02.00

Annotation

Turns on and off various parts of the display annotation. The annotation is divided up into four categories:

1. Meas Bar: This is the measurement bar at the top of the screen. It does not include the settings panel or

the Active Function. Turning off the Meas Bar turns off the settings panel and the Active Function. When
the Meas Bar is off, the graticule area expands to fill the area formerly occupied by the Meas Bar.

2. Screen Annotation: this is the annotation and annunciation around the graticule, including any

annotation on lines (such as the display line, the threshold line, etc.) This does NOT include the marker
number or the N dB result. When off, the graticule expands to fill the entire graticule area.

3. Trace annotation: these are the labels on the traces, showing their detector (or their math mode).

4. Active Function annotation: this is the active function display in the meas bar, and all of the active

function values displayed on softkeys.

See the figure below. Each type of annotation can be turned on and off individually.

648

Sequence Analyzer User's & Programmer's Reference

«
...
646
647
648
649
650
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E6650A EXF

Бренд: NEC Страницы: 54

Бренд: GE Страницы: 698

Бренд: Bahco Страницы: 9

Бренд: CAE Healthcare Страницы: 108

Бренд: Cannon Страницы: 36

Бренд: Ecler Страницы: 108

Бренд: R&S Страницы: 121

Бренд: Pablo Страницы: 7

Бренд: EuroLite Страницы: 28

Бренд: Raymarine Страницы: 124

Бренд: Raymarine Страницы: 192

Бренд: Magma Страницы: 16

Бренд: XanLite Страницы: 2

Бренд: X-Rite Страницы: 6

Бренд: Makita Страницы: 208

Бренд: Masterclock Страницы: 19

LUNAQUA Classic LED

Бренд: Oase Страницы: 16

Бренд: Omcan Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды