Keysight E3630A Скачать руководство пользователя

Страница: 8 / 71

Keysight E3630A Operating and Service Manual

Regulatory Markings

The CE mark is a registered trademark

of the European Community. This CE

mark shows that the product complies

with all the relevant European Legal

Directives.

The CSA mark is a registered

trademark of the Canadian

Standards Association.

The RCM mark is a registered

trademark of the Australian

Communications and Media Authority.

This symbol indicates the time period

during which no hazardous or toxic

substance elements are expected to

leak or deteriorate during normal use.

Forty years is the expected useful life

of the product.

This symbol is a South Korean Class A

EMC Declaration. This is a Class A

instrument suitable for professional

use and in electromagnetic

environment outside of the home.

ICES/NMB-001 indicates that this ISM

device complies with the

Canadian ICES-001.

Cet appareil ISM est conforme a la

norme NMB-001 du Canada.

This instrument complies with the

WEEE Directive (2002/96/EC) marking

requirement. This affixed product label

indicates that you must not discard

this electrical or electronic product in

domestic household waste.

Содержание E3630A








































































Результаты поиска

Содержание E3630A

Отзывы:

Похожие инструкции для E3630A

Бренды по названию

Популярные бренды

Keysight E3630A, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание E3630A

Отзывы:

Похожие инструкции для E3630A

Бренды по названию

Популярные бренды