Keysight E3630A Скачать руководство пользователя | Manualshive

Страница: 6 / 71

background image

6

Keysight E3630A Operating and Service Manual

Safety Considerations

Read the information below before using this instrument.
The following general safety precautions must be observed during all phases of

operation, service, and repair of this instrument. Failure to comply with these

precautions or with specific warnings elsewhere in this manual violates safety

standards for design, manufacture, and intended use of the instrument. Keysight

Technologies assumes no liability for the customer’s failure to comply with these

requirements.
Do not use this product in any manner not specified by the manufacturer. The

protective features of this product may be impaired if it is used in a manner not

specified in the operation instructions.

WARNING

BEFORE APPLYING POWER

Verify that the product is set to match the available line voltage and that the
correct fuse is installed.

WARNING

GROUND THE INSTRUMENT

This product is a Safety Class I instrument (provided with a protective earth
terminal). To minimize shock hazard, the instrument chassis and cabinet
must be connected to an electrical ground. The instrument must be
connected to the AC power supply mains through a three-conductor power
cable, with the third wire firmly connected to an electrical ground (safety
ground) at the power outlet. Any interruption of the protective (grounding)
conductor or disconnection of the protective earth terminal will cause a
potential shock hazard that could result in personal injury. If the instrument
is to be energized via an external autotransformer for voltage reduction, be
certain that the autotransformer common terminal is connected to the
neutral (earthed pole) of the AC power lines (supply mains).

WARNING

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE.

Do not operate the instrument in the presence of flammable gases or fumes.

«
...
4
5
6
7
8
...
»

Содержание E3630A








































































Отзывы:

Нет отзывов

Похожие инструкции для E3630A

Бренд: Omega Страницы: 8

Бренд: Gallagher Страницы: 104

Бренд: Gage Bilt Страницы: 9

Бренд: Gage Bilt Страницы: 13

Бренд: EGAmaster Страницы: 10

Boostamatic 4000

Бренд: Stuart Страницы: 20

Бренд: ModelCraft Страницы: 8

Бренд: OMERA Страницы: 50

Бренд: Lambda Страницы: 14

Бренд: Westfalia Страницы: 18

Бренд: Delta Elektronika Страницы: 21

Бренд: National Instruments Страницы: 47

Бренд: Cembre Страницы: 12

Бренд: TDK-Lambda Страницы: 11

Бренд: Napa Страницы: 12

Бренд: BBT Страницы: 18

PSI 8000 3U HS PV Series

Бренд: Elektro-Automatik Страницы: 76

Бренд: Yokota Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды