manualshive.com logo in svg

Keysight E1458A, Руководство по обслуживанию

Поделиться
Скачать
Keysight E1458A Скачать руководство пользователя страница 40

42

Keysight E1458A 96-Channel Digital I/O Module Service Guide

Service

Troubleshooting

Procedure

1

Verify that the module is correctly installed in the mainframe and that the 
mainframe has passed its power-on test.

2

Send the *TST? command to the device (see example following).

3

The device will return an error code. Any non-zero error code indicates a 
self-test failure. See Table 4-3 for a description of self-test error codes.

Example

An example follows which uses an HP 9000 Series 300 computer with BASIC and 
an multiplexer address of 70918.

10   OUTPUT 70918;"*TST?"Send the self-test command
20   ENTER 70918;AGet response
30   PRINT A
40 END

Disassembly

Use the following procedures and Figure 4-1 to disassemble the Keysight 
E1458A module.

Keysight E1458A Disassembly

1

To remove the covers:

–

Remove the seven T10 Torx screws from the top cover as shown.

–

Lift the top cover off the module.

–

Turn the assembly over and lift off the bottom cover.

2

To remove the front panel:

–

Remove the two T8 Torx screws holding the panel to the A1 PC Assembly 
as shown.

–

Lift the front panel from the A1 assembly.

Содержание E1458A















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды