Keysight DSOX3012T Скачать руководство пользователя страница 80

Страница: 80 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Vertical Controls

The ground level of the signal for each displayed analog channel is identified by
the position of the

icon at the far-left side of the display.

To turn waveforms on or off (channel or math)

Press an analog channel key turn the channel on or off (and to display the

channel's menu).

When a channel is on, its key is illuminated.

You can also do this using the touchscreen. See

“Turn Channels On/Off and

Open Scale/Offset Dialogs"

on page 55.

Channel,
Volts/div

Channel 1
ground
level

Trigger
source

Trigger level
or threshold

Channel 2
ground
level

NOTE

Turning channels off

You must be viewing the menu for a channel before you can turn it off. For example, if channel

1 and channel 2 are turned on and the menu for channel 2 is being displayed, to turn channel

1 off, press

[1]

to display the channel 1 menu; then, press

[1]

again to turn channel 1 off.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды