Keysight DSOX3012T Скачать руководство пользователя страница 76

Страница: 76 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Horizontal Controls

Press

[Navigate]

In the Navigate Menu, press

Navigate

; then, select

Search

Press the

back and forward keys to go to the previous or next search

event.

When searching Serial decode:

• You can press the

stop key to set or clear a mark.

• The

Auto zoom

softkey specifies whether the waveform display is automatically

zoomed to fit the marked row as you navigate.

• Pressing the

Scroll Lister

softkey lets you use the Entry knob to scroll through

data rows in the Lister display.

You can also access navigation controls on the touchscreen. See

“Select Sidebar

Information or Controls"

on page 49.

To navigate segments

When the segmented memory acquisition is enabled and acquisitions are stopped,

you can use the navigation controls to play through the acquired segments.

Press

[Navigate]

In the Navigate Menu, press

Navigate

; then, select

Segments

Press

Play Mode

; then, select:

•

Manual

— to play through segments manually.

In the Manual play mode:

•

Press the

back and forward keys to go to the previous or next

segment.

•

Press the

softkey to go to the first segment.

•

Press the

softkey to go to the last segment.

•

Auto

— to play through segments in an automated fashion.

In the Auto play mode:

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды