Keysight DSOX3012T Скачать руководство пользователя страница 346

Страница: 346 / 530

346

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Utility Settings

•

Press to go

— when you can push the Entry knob to navigate to a new folder

or storage location.

•

Location

— when pointing to a directory that is currently selected.

•

Selected

— when pointing to a file that can be loaded or deleted.

When this label appears, you can press the

Load File

Delete File

softkeys to

take the action.

Pushing the Entry knob is the same as pressing the

Load File

softkey.

A file that has been deleted from a USB storage device cannot be recovered

by the oscilloscope.

Use your PC to create directories on a USB storage device.

USB Storage

Devices

Most USB mass storage devices are compatible with the oscilloscope. However,

certain devices may be incompatible, and may not be able to be read or written to.

USB storage devices must be formatted with the FAT or FAT32 file system format.

When the USB mass storage device is connected to the oscilloscope's front or rear

USB host port, a small four-color circle icon may be displayed briefly as the USB

device is read.

You do not need to "eject" the USB mass storage device before removing it. Simply

ensure that any file operation you've initiated is done, and remove the USB drive

from the oscilloscope's host port.

Do not connect USB devices that identify themselves as hardware type "CD"

because these devices are not compatible with the InfiniiVision X-Series

oscilloscopes.

If two USB mass storage devices are connected to the oscilloscope, the first one is

designated "\usb" and the second one is designated "\usb2".

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды