Keysight DSOX3012T Скачать руководство пользователя страница 277

Страница: 277 / 530

Mask Testing

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

277

To clear the mask and switch off mask testing, press the

Back/Up key to

return to the Mask Test Menu, then press the

Clear Mask

softkey.

If infinite persistence display mode (see

“To set or clear persistence"

on page 157)

is "on" when mask test is enabled, it stays on. If infinite persistence is "off" when

mask test is enabled, it is switched on when mask test is switched on, then infinite

persistence is switched off when mask test is switched off.

Troubleshooting

Mask Setup

If you press

Create Mask

and the mask appears to cover the entire screen, check the

± Y and ± X settings in the Automask Menu. If these are set to zero the resulting

mask will be extremely tight around the waveform.

If you press

Create Mask

and it appears that no mask was created, check the ± Y

and ± X settings. They may be set so large that the mask is not visible.

Mask Test Setup Options

From the Mask Test Menu, press the

Setup

softkey to enter the Mask Setup Menu.

Back

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды