Keysight DSOX3012T Скачать руководство пользователя страница 274

Страница: 274 / 530

274

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Measurements

When enabled, the standard deviation shown in measurement statistics

becomes the standard deviation/mean.

To specify the number of values used when calculating measurement statistics,

press the

Max Count

softkey and enter the desired value.

Statistics are calculated on the most recent "N" number of values, where N is

the either the total number of acquisitions measured or a limited

Max Count

number of acquisitions measured.

Other things to know about measurement statistics:
• When the

[Single]

key is pressed, statistics are reset and a single measurement

is done (count = 1). Successive

[Single]

acquisitions accumulate statistical data

(and the count is incremented).

• The

Increment Statistics

softkey only appears when the acquisition is stopped

and the optional segmented memory feature is off. Press the

[Single]

[Run/Stop]

key to stop the acquisition. You can use the horizontal position

control (in the Horizontal control section of the front panel) to pan through the

waveform. Active measurements will stay on screen, allowing you to measure

various aspects of the captured waveforms. Press

Increment Statistics

to add the

currently measured waveform to the collected statistical data.

• The

Analyze Segments

softkey only appears when the acquisition is stopped and

the optional segmented memory feature is on. After an acquisition has

completed (and the oscilloscope is stopped), you can press the

Analyze

Segments

softkey to accumulate measurement statistics for the acquired

segments.

You can also turn on infinite persistence (in the Display Menu) and press the

Analyze Segments

softkey to create an infinite persistence display.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды