Keysight DSOX3012T Скачать руководство пользователя страница 269

Страница: 269 / 530

Measurements

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

269

The sideband used for the measurement is selected with the Channel Select

parameter. You can select the first through fifth sidebands above or below the

main range (1H through 5H above and 1L through 5L below). The full sideband

must be in the graticule to be measured. Otherwise, the measurement results will

be "Incomplete".

When this measurement is tracked with cursors, the cursors show the sideband

being measured.

Total Harmonic Distortion (THD)

Total Harmonic Distortion

(THD) is the ratio of power in the fundamental frequency to

the power contained in the rest of the harmonics and noise. THD is a measure of

signal purity.

Total Harmonic Distortion

(THD) measures the power contained in the bands

surrounding each harmonic and compares it to the power in the band surrounding

the fundamental frequency. The width of the bands measured is the same for the

fundamental frequency and each harmonic. That width is 1/2 of the fundamental

frequency.

Main

Width

Spacing

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды