Keysight DSOX3012T Скачать руководство пользователя страница 231

Страница: 231 / 530

Acquisition Control

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

231

Measurements, Statistics, and Infinite Persistence with Segmented

Memory

To perform measurements and view statistical information, press

[Meas]

and set up

your desired measurements (see

Chapter 15

, “Measurements,” starting on page

243). Then, press

Analyze Segments

. Statistical data will be accumulated for the

measurements you have chosen.

The

Analyze Segments

softkey appears when the acquisition is stopped and the

segmented memory feature is on or when the serial Lister is enabled.

You can also turn on infinite persistence (in the Display Menu) and press the

Analyze Segments

softkey to create an infinite persistence display.

Segmented Memory Re-Arm Time

After each segment fills, the oscilloscope re-arms and is ready to trigger in about

1 µs.

Remember though, for example: if the horizontal time per division control is set to

5 µs/div, and the Time Reference is set to

Center

, it will take at least 50 µs to fill all

ten divisions and re-arm. (That is 25 µs to capture pre-trigger data and 25 µs to

capture post-trigger data.)

Saving Data from Segmented Memory

You can save either the currently displayed segment (

Save Segment - Current

), or all

segments (

Save Segment - All

) in the following data formats: CSV, ASCII XY, and

BIN.

Be sure to set the Length control to capture enough points to accurately represent

the captured data. When the oscilloscope is busy saving multiple segments,

progress is displayed in the upper right area of the display.

For more information, see

“To save CSV, ASCII XY, or BIN data files"

on page 324.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды