Keysight DSOX3012T Скачать руководство пользователя страница 211

Страница: 211 / 530

Trigger Mode/Coupling

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

211

To enable or disable trigger noise rejection

Noise Rej adds additional hysteresis to the trigger circuitry. By increasing the

trigger hysteresis band, you reduce the possibility of triggering on noise. However,

this also decreases the trigger sensitivity so that a slightly larger signal is required

to trigger the oscilloscope.

Press the

[Mode/Coupling]

key.

In the Trigger Mode and Coupling Menu, press the

Noise Rej

softkey to enable or

disable.

To enable or disable trigger HF Reject

HF Reject adds a 50 kHz low-pass filter in the trigger path to remove high

frequency components from the trigger waveform.

You can use HF Reject to remove high-frequency noise, such as AM or FM

broadcast stations or noise from fast system clocks, from the trigger path.

Press the

[Mode/Coupling]

key.

In the Trigger Mode and Coupling Menu, press the

HF Reject

softkey to enable

or disable.

Pass
Band

50 kHz

0 dB

-3 dB

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды