Keysight DSOX3012T Скачать руководство пользователя страница 191

Страница: 191 / 530

Triggers

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

191

Press the

< Hold

softkey, and turn the Entry knob to select the hold time.

Video Trigger

Video triggering can be used to capture the complicated waveforms of most

standard analog video signals. The trigger circuitry detects the vertical and

horizontal interval of the waveform and produces triggers based on the video

trigger settings you have selected.

The oscilloscope's MegaZoom IV technology gives you bright, easily viewed

displays of any part of the video waveform. Analysis of video waveforms is

simplified by the oscilloscope's ability to trigger on any selected line of the video

signal.

Press the

[Trigger]

key.

NOTE

It is important, when using a 10:1 passive probe, that the probe is correctly compensated. The

oscilloscope is sensitive to this and will not trigger if the probe is not properly compensated,

especially for progressive formats.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды