Keysight DSOX3012T Скачать руководство пользователя страница 175

Страница: 175 / 530

Triggers

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

175

Press the

Arm A

softkey, and turn the Entry knob to select the channel on

which the arming edge will occur.

Press the

Slope A

softkey to specify which edge of the Arm A signal will arm

the oscilloscope.

Press the

Trigger B

softkey, and turn the Entry knob to select the channel on

which the trigger edge will occur.

Press the

Slope B

softkey to specify which edge of the Trigger B signal will

trigger the oscilloscope.

Adjust the trigger level for the selected analog channel by turning the Trigger

Level knob. Press the

[Digital]

key and select

Thresholds

to set the threshold level

for digital channels. The value of the trigger level or digital threshold is

displayed in the upper-right corner of the display.

Press the

Back/Up key to return to the Trigger Menu.

Press the

Delay

softkey; then, turn the Entry knob to enter the delay time

between the Arm A edge and the Trigger B edge.

Press the

Nth Edge B

softkey; then, turn the Entry knob to select the Nth edge of

the Trigger B signal to trigger on.

Pulse Width Trigger

Pulse Width (glitch) triggering sets the oscilloscope to trigger on a positive or

negative pulse of a specified width. If you want to trigger on a specific timeout

value, use

Pattern

trigger in the Trigger Menu (see

“Pattern Trigger"

on page 178).

Press the

[Trigger]

key.

In the Trigger Menu, press the

Trigger

softkey; then, turn the Entry knob to

select

Pulse Wid th

Back

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды