Keysight DSOX3012T Скачать руководство пользователя страница 172

Страница: 172 / 530

172

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Triggers

Edge Trigger

The Edge trigger type identifies a trigger by looking for a specified edge (slope)

and voltage level on a waveform. You can define the trigger source and slope in

this menu. The trigger type, source, and level are displayed in the upper-right

corner of the display.

On the front panel, in the Trigger section, press the

[Trigger]

key.

In the Trigger Menu, press the

Trigger

softkey, and use the Entry knob to select

Edge

Select the trigger source:

•

Analog channel,

to the number of channels

•

Digital channel (on mixed-signal oscilloscopes),

to the number of digital

channels minus one.

•

External

— triggers on the EXT TRIG IN signal.

•

Line

— triggers at the 50% level of the rising or falling edge of the AC power

source signal.

•

WaveGen

— triggers at the 50% level of the rising edge of the waveform

generator output signal. (Not available when the DC, Noise, or Cardiac

waveforms are selected.)

•

WaveGen Mod (FSK/FM)

— when waveform generator FSK or FM modulation is

used, triggers at the 50% level of the rising edge of the modulating signal.

You can choose a channel that is turned off (not displayed) as the source for the

edge trigger.

The selected trigger source is indicated in the upper-right corner of the display

next to the slope symbol:

•

through

= analog channels.

•

through

= digital channels.

•

= External trigger input.

•

= Line trigger.

•

= Waveform generator.

Press the

Slope

softkey and select:

•

Rising

edge.

•

Falling

edge.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды