Keysight 53210A Скачать руководство пользователя страница 81

Страница: 81 / 247

53210A Measurements

Keysight 53210A User’s Guide

Reference Oscillator Configuration

53210A measurements are based on a reference oscillator - also referred to as an

internal/external clock or time base. A valid reference oscillator signal must be

present for measurements to occur.
The following information applies to the counter’s standard temperature

compensated crystal oscillator (TCXO) and Option 010 Ultra High-Stability

oven-controlled crystal oscillator (OCXO) references.

Reference Oscillator Source

The reference oscillator (time base) is either the counter’s internal oscillator or the

internal oscillator tuned to an external reference. The source commands are:

[SENSe:]ROSCillator:SOURce {INTernal|EXTernal}

[SENSe:]ROSCillator:SOURce?

(query form)

[SENSe:]ROSCillator:SOURce:AUTO {OFF|ON}

[SENSe:]ROSCillator:SOURce:AUTO?

(query form)

Содержание 53210A
























































































































































































































































Результаты поиска

Содержание 53210A

Отзывы:

Похожие инструкции для 53210A

Бренды по названию

Популярные бренды

Keysight 53210A, Руководство пользователя

Результаты поиска

Содержание 53210A

Отзывы:

Похожие инструкции для 53210A

Бренды по названию

Популярные бренды