Keysight 53210A Скачать руководство пользователя

Страница: 64 / 247

53210A Software Installation and Interface Configuration

Keysight 53210A User’s Guide

Disabling the LAN Interface

The LAN interface can be disabled from the front panel by selecting

I/O Config

followed by

LAN Off

and cycling power on the instrument. When disabled, the

interface cannot be configured by the Connection Expert utility.

Opening the Web Interface from Keysight Connection Expert

The LAN interface is the

only

IO interface from which the counter’s Web-enabled

user interface can be accessed. To open the Web UI, click

in the icon group at

the top of the screen; the web page opens in a browser.

Configuring the USB Interface

The 53210A is a high-speed USB 2.0 device. Connection to the instrument is

through the Type B USB connector located on the instrument rear panel.

Adding Instruments to the USB Configuration

With the 53210A and PC connected through the USB cable, start Keysight

Connection Expert (

Figure 2-4

) if it is not already open. The PC should detect the

presence of the USB device. If necessary, right-click the USB interface (USB0) and

then select

Rescan this Interface

Connection Expert will attempt to establish a communication path to the

instrument. If successful, the instrument will be added to the list of USB
configured instruments (

Figure 2-4

). The USB address can be read from the front

panel as shown below.

NOTE

The first time the 53210A is connected to the PC via the USB cable, a “hardware

wizard” utility within the PC

may

start and prompt you for installation software

for the product. There is no installation software for the USB interface other than

the libraries on the Keysight Automation-Ready CD that ships with the 53210A.

Continue through the “wizard” application

without

searching for software and

using the default selections.

Содержание 53210A
























































































































































































































































Результаты поиска

Содержание 53210A

Отзывы:

Похожие инструкции для 53210A

Бренды по названию

Популярные бренды

Keysight 53210A, Руководство пользователя

Результаты поиска

Содержание 53210A

Отзывы:

Похожие инструкции для 53210A

Бренды по названию

Популярные бренды