Keysight Technologies U3050BH11 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 48

background image

U3050BH11

System Setup with N5245A

System Setup with N5245A

Preparing the N5245A Network Analyzer

1.

Remove the feet from the bottom of the network analyzer.

2.

Remove the

two

lower standoffs and screws (0515-1619) from the rear panel on the

network analyzer.

Figure

5

Rear Bottom Feet

3. Install the two rear locking feet (5023-0132) onto the PNA-X, using the included screws

(0515-1619), where the standoffs were removed.

Figure

6

Install Locking Feet on PNA-X

Standoffs (x2)

Feet (x4)

Locking Feet

Screws (0515-1619)
included in package

(5023-0132)

Keysight U3050BH11 User's and Service Guide

9

«
...
11
12
13
14
15
...
»

Содержание U3050BH11

















































Отзывы:

Нет отзывов

Похожие инструкции для U3050BH11

Бренд: DARAY Страницы: 28

Бренд: MacDon Страницы: 88

Бренд: Jiffy Страницы: 15

Бренд: Modulate Страницы: 2

Бренд: Maeda Страницы: 276

Бренд: Nautilus Страницы: 17

Бренд: National Instruments Страницы: 6

QNET Physics and Dynamics

Бренд: Quanser Страницы: 4

Бренд: Lalizas Страницы: 12

BOBCAT 130 Series

Бренд: Balcrank Страницы: 12

Бренд: GAPOSA Страницы: 32

UG 2200 Special

Бренд: Amazone Страницы: 252

Бренд: HOFFEN Страницы: 22

Бренд: KEP Страницы: 33

Бренд: Hedson Страницы: 32

Бренд: JLG Страницы: 165

Бренд: Labconco Страницы: 174

Бренд: Bavis Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды