Keysight Technologies U3022AH10 Скачать руководство пользователя страница 19

Страница: 19 / 92

U3022AH10

Front and Rear Panel Features

Figure

Rear Panel (Multiport Test Set)

Test Set Interface Pass Through Interface

Line Module

Voltage Adjust

DUT

Control
Connector

Control Lines and Voltage Adjust

For further information pertaining to control lines and voltage adjustments see

“DUT Control Lines” on

page

Test Set Interface

The Test Set Interface connector is used to send address and data to the Test Set from the PNA-X.

Pass Through Interface

Connection to another Test Set.

Line Module

The line fuse, as well as a spare, reside within the line module.

Figure

on page

illustrates where the

fuses are located and how to access them.

U3022AH10 User's and Service Guide

Содержание U3022AH10





























































































Результаты поиска

Содержание U3022AH10

Отзывы:

Похожие инструкции для U3022AH10

Бренды по названию

Популярные бренды

Keysight Technologies U3022AH10, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U3022AH10

Отзывы:

Похожие инструкции для U3022AH10

Бренды по названию

Популярные бренды