Keysight Technologies S9100A Скачать руководство пользователя страница 91

Страница: 91 / 107

7 Run Power Calibration

S9100A 5G Multi-Band Vector Transceiver, Startup Guide

7. 3. 6. 2 Calibration 2 of 2: Power from RRH 1 RFHD 2 -> RRH 1 RFHD 1

This calibration is used to calibrate FR2 ports
(with

RF Tx/Rx 2

➁

used as the RF Output) on an

S9100A Option 022 mmWave Transceiver
with High IF and Blocker.

When performing this Power Calibration, the Source (Tx) output
power level is set to -5 dBm by default. The power level from
M9410A PXIe VXT #1 is calibrated while the RF Output for
M9410A PXIe VXT #2 is set to Off.

1. Calibrate the Source (Tx) signal path

a. Select the Power Calibration tab.

b. Select the Operation drop-down arrow and select

Calibration

c. Select the Calibration Step(s) drop-down arrow and select

Complete

d. Select the Port Selection drop-down arrow and

select

RRH 1 RFHD 2 -> RRH 1 RFHD 1

e. Select

Start the calibration

and follow the prompts.

f. Connect the U8487A Power Sensor or equivalent to

M1740A mmWave Transceiver connector

RF Tx/Rx 2

➁

g. Select

to continue the calibration.

View the

Results Source

tab when the calibration is complete.

Corrections are stored in:

S9100ID_<SerialNumber>-

Tx-RFIO_2-CHANNELPOWER.csv

Содержание S9100A












































































































Результаты поиска

Содержание S9100A

Отзывы:

Бренды по названию

Популярные бренды

Keysight Technologies S9100A, Руководство для стартапов

Результаты поиска

Содержание S9100A

Отзывы:

Бренды по названию

Популярные бренды