Keysight Technologies PD1000A Скачать руководство пользователя

Страница: 40 / 44

Keysight PD1000A Power Device Measurement System

Use Proper SMA Connector Care and Connection Techniques

Final Connection Using a Torque Wrench

Using a torque wrench guarantees the connection is not too tight, preventing

possible connector damage. It also guarantees that all connections are equally

tight. Prevent the rotation of anything other than the connector nut that you are

tightening.
Use a Keysight 8710-1582, 0.56N-m (5 lb-in) 5/16 inch break-over torque

wrench to make a final connection. A Torque wrench is supplied as part of the

PD1000A-SPK Accessory Kit.

Turn the connector nut. This may be possible to do by hand if one of the

connectors is fixed (as on a test port). However, it is recommended that you

use a second open-end wrench to keep the body of the device from turning.

Position both wrenches within 90 degrees of each other before applying force.

Wrenches opposing each other (greater than 90 degrees apart) will cause a

lifting action that can misalign and stress the connections of the device

involved. This is especially true when several devices are connected together.

Refer to the following figure.

Figure 7

Keysight 8710-1582 SMA Torque Wrench

The Keysight 8710-1582, 5 lb-in Torque Wrench is a precision

instrument and should be treated and maintained like a measuring

instrument.

Figure 8

Wrench Positions

Hold this

wrench

steady

Lift

Device

Correct method

Incorrect method

(reduces lift on connection)

(too much lift on connection)

Содержание PD1000A













































Результаты поиска

Содержание PD1000A

Отзывы:

Похожие инструкции для PD1000A

Бренды по названию

Популярные бренды

Keysight Technologies PD1000A, Руководство по эксплуатации

Результаты поиска

Содержание PD1000A

Отзывы:

Похожие инструкции для PD1000A

Бренды по названию

Популярные бренды