Keysight Technologies PD1000A Скачать руководство пользователя | Manualshive

Страница: 17 / 44

background image

Keysight PD1000A Test Fixture Operating Guide

17

PD1000A Surface Mount Device Test Fixture

PD1000A Surface Mount Device Test Fixture

Keysight’s PD1000A SMD Test Fixture is designed for testing surface mount

device packages such as the 7-pin TO-263 (also known as D

2

PAK or DDPAK)

SMD devices. Other SMD devices may also be tested with the SMD Test Fixture.

This test fixture provides a clamp to hold the SMD in place while the tests are

running.

Inserting Devices into the SMD Test Fixture

Figure 9 shows the proper orientation for inserting Surface Mount Devices (SMD)

into the Test Fixture. Always observe proper orientation when inserting devices.

Gently place the device into the Frame Guide of the Test Fixture. Ensure it is

properly aligned with the PC Board contact pattern. Ensure the SMD device fits

securely and completely into the positioning frame guide. Press the Test Fixture

handle down until it latches to firmly hold the device in place while being tested.
The frame guide provided with the SMD test fixture is for devices with

dimensions: 10 mm wide and 15 mm top of tab to bottom of pins.

Figure 8

Keysight PD1000A Surface Mount Device Test Fixture

Drain/Collector SMA

Connector to Bias T to

Port 2 on the ENA

Network Analyzer

Gate SMA Connector

to Bias T to Port 1 on

the ENA Network

Analyzer

Make certain the Test Fixture work station is ESD protected. See

“Static-safe Handling Procedures” on page 11 for details.

«
...
15
16
17
18
19
...
»

Содержание PD1000A













































Отзывы:

Нет отзывов

Похожие инструкции для PD1000A

Endura AZ20 series

Бренд: ABB Страницы: 8

Бренд: Valeport Страницы: 25

Бренд: 3B6 Страницы: 30

Бренд: Han Seung Страницы: 2

Бренд: Hammond Страницы: 78

Orion Versa Star Pro Series

Бренд: Thermo Scientific Страницы: 4

Бренд: RS PRO Страницы: 44

Бренд: Teledyne Страницы: 85

Liebert MBX Busway

Бренд: Vertiv Страницы: 16

Бренд: Percussion Play Страницы: 3

Бренд: Saab Страницы: 116

Бренд: Fluke Страницы: 97

Бренд: Hanna Instruments Страницы: 24

Бренд: Vaisala Страницы: 96

Class 3400 Meter

Бренд: E-Mon Страницы: 20

ARCTIC SUN Simply Advanced 5000

Бренд: Medivance Страницы: 274

Бренд: U.S. Divers Страницы: 63

Бренд: Oakton Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды