manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя, Страница: 40 / 369

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 40

 40                                                                                               N5511A Phase Noise Test System User’s Guide

Expanding Your Measurement Experience
GUI Features

GUI Features

Viewing Markers

The marker function allows you to display the exact frequency and amplitude 

of any point on the results graph. 
To access the marker function, on the 

View

 menu, click 

Markers

. In the dialog 

box containing Marker buttons at the bottom of the application, up to nine 

markers may be added. To add a marker, click 

Add Marker 

at the bottom of 

the display and to remove a highlighted marker, click the 

Delete Marker

 

button at the bottom of the display. Markers are added to the latest measured 

trace on the display.

Figure 4-1 

View Markers

Figure 4-2 

Add/Delete Markers

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов