manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 285

N5511A Phase Noise Test System User’s Guide                                                                                                 285

Baseband Noise Measurement Example
Baseband Noise with Test Set Measurement Example

Baseband Noise with Test Set Measurement Example

This measurement example will help you measure the noise voltage of a 

source.

Define Measurement

At the top of the main application window, click "Define" and then select 

"Measurement…" from the drop-down menu.

Define

, 

Measurement

, 

Measurement Type: Baseband Noise (using test set)

Connect a noise source to the test set using one of the configurations as shown 

in 

Figure 13-1

.

New Measurement

Close Define Window. From the File Menu: 

Measure

, 

New Measurement

. 

When the "Do you want to perform a New Calibration and Measurement?" 

prompt appears, click 

Yes

.

To ensure accurate measurements allow the DUT and measurement equipment to warm up at 

least 30 minutes before making the noise measurement. 

Ensure there is no DC present in the signal at the inputs to the test set to prevent damage to the 

test set.

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды