manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 202

 202                                                                                               N5511A Phase Noise Test System User’s Guide

Residual Measurement Examples
Amplifier Measurement Example - Dual Channel

Amplifier Measurement Example - Dual Channel

This example contains information about measuring the residual noise of 

two-port devices. It demonstrates a residual phase noise measurement for an 

RF Amplifier. Refer to 

Chapter 7, “Residual and Additive Noise Measurement 

Fundamentals”

 for more information about residual phase noise 

measurements.

Required equipment

— RF amplifier
— Stimulus source (at frequency under test) - for this example, an E8257D 

PSG will be used

— RF  calibration  source
— Coaxial cables and adapters necessary to connect the DUT and reference 

source to the test set.

Connections

Setup the measurement using the following connection diagram.

Figure 8-10 

Setup for Dual Channel measurement

To prevent damage to the test system’s hardware components, verify that the input signal is 

within the test system’s power limits. Refer to the N5511A Data Sheet online.

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды