Keysight Technologies N5221A Скачать руководство пользователя

Страница: 96 / 368

4-22 Keysight N5221A/22A Service Guide

Troubleshooting
Rear Panel Troubleshooting

If the Window Desktop is not displayed, press UTILITY

, then

to view the Windows Taskbar menu at

the bottom of the display.

On the

Windows Taskbar

menu, click Start then point to

Programs,

National Instruments NI-488.2,

and then click

Explore GPIB

to open the

Measurement & Automation

window.

On the left side of the

Measurement & Automation

window under folders:

Click the plus sign to expand the

Measurement

Automation

folder.

Click the plus sign to expand the

Devices and Interfaces

folder.

Right click

GPIB0 (AT-GPIB/TNT)

to open a submenu.

On the submenu, click

Scan for Instruments

to run the test.

The state of all the peripherals found on the bus is returned.

If problems are detected, check the connections of all GPIB cables, and
check all the GPIB addresses of the instruments on the bus.

Troubleshooting Systems with Controllers

Passing the preceding test indicates that the analyzer's peripheral functions

are operating normally. Therefore, if the analyzer has not been operating

properly with an external controller, check the following:

— The GPIB interface hardware is incorrectly installed or not operational.

(Refer to the embedded help in your analyzer.)

— The programming syntax is incorrect. (Refer to the embedded help in your

analyzer.)

LAN Troubleshooting

Problems with the Local Area Network (LAN) can be difficult to solve. Software

and protocol problems can make it difficult to determine whether the

analyzer's hardware is working properly, or if there is a problem with the LAN or

cabling.

System

Configure

Control Panel

...

Address Information

—

Each device must have its own unique address.

—

The network analyzer’s default GPIB address in the controller mode is

21.

—

The address set on each device must match the one recognized by the

analyzer (and displayed).
Refer to the manual of the peripheral to read or change its address.

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды