Keysight Technologies N5221A Скачать руководство пользователя страница 115

Страница: 115 / 368

Keysight N5221A/22A Service Guide 4-41

Troubleshooting
Measurement System Troubleshooting

— A25, A26, A27, or A28 receiver coupler

— A34, A35, A36, or A37 source step attenuator

— A38, A39, A40, or A41 bias tee

— A29, A30, A31, or A32 test port coupler

Equipment Used for These Tests

To determine which assembly is defective, check the signal at each available

measurement point in the signal path from the output of the source board to

the output port.
Set the network analyzer for an S

11, S22, S33, or S44,

measurement for Port 1, 2,

3, or 4 respectively, with a CW frequency of 800 MHz.
Perform the following checks in the order presented.

Checking the A25, A26, A27, and A28 Receiver Couplers

Locate the appropriate semirigid cable at the output of the receiver

coupler to be checked:

—

Options 200 and 400

—

Port 1; W11 of A25

—

Port 2; W23 of A28

—

Port 3; W15 of A26

—

Port 4; W19 or A27

—

Options 219 and 419

—

Port 1; W71 of A25

—

Port 2; W83 of A28

—

Port 3; W75 of A26

—

Port 4; W79 of A27

Using a 5/16-inch torque wrench, disconnect the semirigid cable at the

receiver coupler.

Connect the spectrum analyzer to the open receiver coupler connector.

Set the spectrum analyzer to measure a signal at 800 MHz.

Equipment Type

Model or

Part Number

Alternate Model or Part

Number

Spectrum analyzer

8565E

856xE

a. Must be capable of measuring a signal at 1 GHz.

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Keysight Technologies N5221A, Руководство по обслуживанию, Страница: 115 / 368

Результаты поиска

Содержание N5221A

Отзывы: