Keysight Technologies M1740A Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 39

background image

12 Getting Started Guide

Safety & Environmental Information
Ventilation

Ventilation

Power requirements

The M1740A does not have an AC power connection. It is powered by a DC

voltage from the E7760B Wideband Transceiver or the E7770A Common

Interface Unit; this voltage is supplied over the RF Cable Assembly to the

LO/Pwr/Ctrl/IF In

connector. The DC supply does not represent a risk of

personal injury.

Using Accessories

When the M1740A is used in connection with the E7760B Wideband

Transceiver or the E7770A Common Interface Unit, use only the RF Cable

Assembly that was supplied with the M1740A to connect it with the other
instrument, and connect it only to the mmW ports on that instrument.

VENTILATION REQUIREMENTS: When installing the instrument(s) into a

cabinet, consideration shall be given to the convection flow into and out of the

cabinet. Consideration shall also be given to the individual instruments to avoid

having the heated discharge of one instrument, now becoming the cooling

intake air for another instrument.

Another area of concern is verification that the maximum ambient operating

temperature of the instrument(s) is not exceeded by cabinet installation.

Keysight recommends forced air convection whenever an instrument(s) are

installed in a cabinet and further recommends that the maximum operating

temperature of the cabinet be reduced 10°C from the lowest, of the maximum

operating temperature of a single instrument.

If there are any concerns or special requirements an Keysight Field Engineer

should be consulted to assure instrument(s) temperature compliance and

performance.used.

The RF Cable Assembly should not be connected to, or disconnected from, the

M1740A while it is suppling DC power from the E7760B or E7770A. This

connection should be made only when the E7760B is powered off, or the cable

is not connected to the E7760B or E7770A. If the LED status indicator on the

front of the M1740A is lit, this indicates that it is powered up and the cable

should not be disconnected.

«
...
10
11
12
13
14
...
»

Содержание M1740A








































Отзывы:

Нет отзывов

Похожие инструкции для M1740A

Бренд: ABB Страницы: 2

Бренд: Harman Kardon Страницы: 13

Бренд: Ramsey Electronics Страницы: 28

Бренд: Yaesu Страницы: 4

Бренд: YouKits Страницы: 1

Бренд: Xblitz Страницы: 76

AMG3787E-1-DR-1550-HP

Бренд: AMG Страницы: 12

Centronic VarioControl VC420

Бренд: Becker Страницы: 52

Бренд: Leviton Страницы: 2

Бренд: Onkyo Страницы: 102

Бренд: Magnat Audio Страницы: 54

Бренд: Ranger Communications Страницы: 11

Бренд: Hallicrafters Страницы: 8

Бренд: Sangean Страницы: 52

Бренд: JAMO Страницы: 142

Бренд: dB Страницы: 101

Бренд: Pro2 Страницы: 4

Бренд: Portech Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды