Keysight Technologies InfiniVision 6000L Series Скачать руководство пользователя страница 22

Страница: 22 / 100

6000L Series Oscilloscopes Service Guide

Testing Performance

To construct the test connector (for use with MSO models only)

Keysight 6000L Series Oscilloscopes that have digital channels enabled require

the test connector described below. Follow the steps to build the test connector.

Obtain a BNC connector and an 8-by-2 section of Berg strip.

On one side of the Berg strip, solder a jumper wire to all of the pins (shown in

Figure 1

on page 23).

On the other side of the Berg strip, solder another jumper wire to all of the pins.

Solder the center of the BNC connector to a center pin on one of the rows on

the Berg strip.

Solder the ground tab of the BNC connector to a center pin on the other row on

the Berg strip.

Table 3

Materials required to construct the test connectors

Description

Recommended Part

Qty

BNC (f) Connector

Keysight 1250-1032 or

Pomona 4578

Berg Strip, 8-by-2

Jumper wire

Содержание InfiniVision 6000L Series





































































































Результаты поиска

Содержание InfiniVision 6000L Series

Отзывы:

Похожие инструкции для InfiniVision 6000L Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniVision 6000L Series, Руководство по обслуживанию

Результаты поиска

Содержание InfiniVision 6000L Series

Отзывы:

Похожие инструкции для InfiniVision 6000L Series

Бренды по названию

Популярные бренды