Keysight Technologies InfiniVision 6000L Series Скачать руководство пользователя страница 15

Страница: 15 / 100

Characteristics and Specifications

6000L Series Oscilloscopes Service Guide

Measurement Category

The InfiniiVision oscilloscopes are not intended to be used for measurements in

Measurement Category II, III, or IV.

Measurement Category Definitions

The "Not rated for CAT II, III, IV" measurement category is for measurements

performed on circuits not directly connected to MAINS. Examples are

measurements on circuits not derived from MAINS, and specially protected

(internal) MAINS derived circuits. In the latter case, transient stresses are variable;

for that reason, the transient withstand capability of the equipment is made known

to the user.

Measurement category II is for measurements performed on circuits directly

connected to the low voltage installation. Examples are measurements on

household appliances, portable tools and similar equipment.

Measurement category III is for measurements performed in the building

installation. Examples are measurements on distribution boards, circuit-breakers,

wiring, including cables, bus-bars, junction boxes, switches, socket-outlets in the

fixed installation, and equipment for industrial use and some other equipment, for

example, stationary motors with permanent connection to the fixed installation.

Measurement category IV is for measurements performed at the source of the

low-voltage installation. Examples are electricity meters and measurements on

primary overcurrent protection devices and ripple control units.

WARNING

Use this instrument only for measurements within its specified measurement category
(not rated for CAT II, III, IV). No transient overvoltages allowed.

Содержание InfiniVision 6000L Series





































































































Результаты поиска

Содержание InfiniVision 6000L Series

Отзывы:

Похожие инструкции для InfiniVision 6000L Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniVision 6000L Series, Руководство по обслуживанию

Результаты поиска

Содержание InfiniVision 6000L Series

Отзывы:

Похожие инструкции для InfiniVision 6000L Series

Бренды по названию

Популярные бренды