Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 308

Страница: 308 / 432

308

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Utility Settings

Adding an Annotation

You can add an annotation to the upper left corner of the oscilloscope's display.

The annotation is useful for documentation purposes, to add notes before

capturing screens.

To add an annotation:

On the oscilloscope's front panel, press

[Utility]

In the Utility Menu, press

Annotation

In the Annotation Menu, press

Annotation

to enable the annotation.

Press

Edit

In the Edit Annotation Menu:

•

Use the

Spell

, , ,

and

Delete Character

softkeys to enter the annotation

text:

•

Spell

— press this softkey and turn the Entry knob to select the character

at the current position.

•

— press this softkey to enter characters and move the cursor to the

next character position.

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды