Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 30

Страница: 30 / 432

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Getting Started

When using the oscilloscope in a bench-top setting, provide at least 2" clearance

at the sides and 4" (100 mm) clearance above and behind the oscilloscope for

proper cooling.

To power-on the

oscilloscope

Connect the power cord to the rear of the oscilloscope, then to a suitable AC

voltage source. Route the power cord so the oscilloscope's feet and legs do not

pinch the cord.

Install the instrument so that the detachable power cord is readily identifiable

and is easily reached by the operator. The detachable power cord is the

instrument disconnecting device. It disconnects the mains circuits from the

mains supply before other parts of the instrument. The front panel switch is only

a standby switch and is not a LINE switch. Alternatively, an externally installed

switch or circuit breaker (which is readily identifiable and is easily reached by

the operator) may be used as a disconnecting device.

The oscilloscope automatically adjusts for input line voltages in the range 100

to 240 VAC. The line cord provided is matched to the country of origin.

Press the power switch.

The power switch is located on the lower left corner of the front panel. The

oscilloscope will perform a self-test and will be operational in a few seconds.

Connect Probes to the Oscilloscope

Connect the oscilloscope probe to an oscilloscope channel BNC connector.

Connect the probe's retractable hook tip to the point of interest on the circuit or

device under test. Be sure to connect the probe ground lead to a ground point

on the circuit.

WARNING

Always use a grounded power cord. Do not defeat the power cord ground.

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды