Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 298

Страница: 298 / 432

298

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Utility Settings

If the ground level is off screen, the waveform will expand about the top or

bottom edge of the screen based on where the ground is off screen.

•

Center

— The displayed waveform will expand about the center of the display.

To disable/enable transparent backgrounds

There is a preference setting for whether measurements, statistics, reference

waveform information, and other text displays have transparent or solid

backgrounds.

Press

[Utility] > Options > Preferences

Press

Transparent

to toggle between transparent and solid text display

backgrounds.

To load the default label library

See

"To reset the label library to the factory default"

on page 139.

To set up the screen saver

The oscilloscope can be configured to turn on a display screen saver when the

oscilloscope has been idle for a specified length of time.

Press

[Utility] > Options > Preferences > Screen Saver

to display the Screen Saver

Menu.

Press the

Saver

softkey to select the screen saver type.

The screen saver can be set to

Off

, to display any of the images shown in the

list, or can display a user-defined text string.

User

is selected, press the

Spell

softkey to select the first character of the text

string. Use the Entry knob to choose a character. Then press the

Enter

softkey

to advance to the next character and repeat the process.

NOTE

You can use a connected USB keyboard instead of using the

Spell

(and other) character

editing softkeys.

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды