Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 295

Страница: 295 / 432

Utility Settings

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

295

File Explorer

The File Explorer lets you navigate the oscilloscope's internal file system and the

file systems of connected USB storage devices.

From the internal file system, you can load oscilloscope setup files or mask files.

From a connected USB storage device, you can load setup files, mask files, license

files, firmware update (*.ksx) files, label files, etc. Also, you can delete files on a

connected USB storage device.

The oscilloscope's internal file system, under "\User Files", consists of 10 locations

for oscilloscope setup files, and four locations for mask files.

To use the File Explorer:

Press

[Utility] > File Explorer

In the File Explorer Menu, press the softkey in the first position and use the

Entry knob to navigate.

NOTE

The USB port on the front panel, and the USB port on the rear panel labeled "HOST" are USB

Series A receptacles. These are the receptacles to which you can connect USB mass storage

devices and printers.
The square receptacle on the rear panel labeled "DEVICE" is provided for controlling the

oscilloscope over USB. See the

Programmer's Guide

for more information.

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя, Страница: 295 / 432

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы: