Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 269

Страница: 269 / 432

Waveform Generator

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

269

•

Exponential Rise

•

Exponential Fall

When the

Ramp

shape is selected, a

Symmetry

softkey appears so that you can

specify the amount of time per cycle that the ramp waveform is rising.

Press the

AM Freq

softkey and turn the Entry knob to specify the frequency of

the modulating signal.

Press the

AM Depth

softkey and turn the Entry knob to specify the amount of

amplitude modulation.

AM Depth refers to the portion of the amplitude range that will be used by the

modulation. For example, a depth setting of 80% causes the output amplitude

to vary from 10% to 90% (90% – 10% = 80%) of the original amplitude as the

modulating signal goes from its minimum to maximum amplitude.

The following screen shows an AM modulation of a 100 kHz sine wave carrier

signal.

To set up Frequency Modulation (FM)

In the Waveform Generator Modulation Menu (under

[Wave Gen] > Settings >

Modulation

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя, Страница: 269 / 432

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы: