Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 176

Страница: 176 / 432

176

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Trigger Mode/Coupling

To select the Auto or Normal trigger mode

When the oscilloscope is running, the trigger mode tells the oscilloscope what to

do when triggers are not occurring.

In the

Auto

trigger mode (the default setting), if the specified trigger conditions are

not found, triggers are forced and acquisitions are made so that signal activity is

displayed on the oscilloscope.

In the

Normal

trigger mode, triggers and acquisitions only occur when the

specified trigger conditions are found.

To select the trigger mode:

Press the

[Mode/Coupling]

key.

In the Trigger Mode and Coupling Menu, press the

Mode

softkey; then select

either

Auto

Normal

See the following

"When to Use Auto Trigger Mode"

on page 177 and

"When

to Use Normal Trigger Mode"

on page 177 descriptions.

You can also configure the

[Quick Action]

key to toggle between the Auto and

Normal trigger modes. See

"Configuring the [Quick Action] Key"

on page 307.

Triggering and the

Pre- and

Post-Trigger

Buffers

After the oscilloscope starts running (after pressing

[Run]

[Single]

or changing

the trigger condition), the oscilloscope first fills the pre-trigger buffer. Then, after

the pre-trigger buffer is filled, the oscilloscope starts searching for a trigger, and

sampled data continues to flow data through the pre-trigger buffer in a first-in

first-out (FIFO) manner.

When a trigger is found, the pre-trigger buffer contains the events that occurred

just before the trigger. Then, the oscilloscope fills the post-trigger buffer and

displays the acquisition memory. If the acquisition was initiated by

[Run/Stop]

, the

process repeats. If the acquisition was initiated by pressing

[Single]

, the acquisition

stops (and you can Pan and Zoom the waveform).

In either Auto or Normal trigger mode, a trigger may be missed if the event occurs

while the pre-trigger buffer is being filled. This may be more likely, for example,

when the horizontal scale knob is set to a slow time/div setting, such as

500 ms/div.

Trigger Indicator

The trigger indicator at the top right of the display shows whether triggers are

occurring.

In the

Auto

trigger mode, the trigger indicator can show:

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды