Keysight Technologies InfiniiVision 2000 Скачать руководство пользователя страница 64

Страница: 64 / 86

2000/3000 X-Series Oscilloscopes Service Guide

Troubleshooting

Solving General Problems with the Oscilloscope

This section describes how to solve general problems that you may encounter

while using the Keysight 2000/3000 X-Series oscilloscopes.

After troubleshooting the oscilloscope, if you need to replace parts, refer to

Chapter 6

, “Replaceable Parts,” starting on page 73.

If there is no display

✔

Check that the power cord is firmly seated in the oscilloscope power

receptacle.

✔

Check that the power source is live.

✔

Check that the front-panel power switch is on.

✔

If there is still no display, go to the troubleshooting procedures in this chapter.

If there is no trace display

✔

Check that the Intensity (on the front panel) is adjusted correctly.

✔

Recall the default setup by pressing

[Default Setup]

. This will ensure that the

trigger mode is Auto.

✔

Check that the probe clips are securely connected to points in the circuit under

test, and that the ground is connected.

✔

Check that the circuit under test is powered on.

✔

Press the

[AutoScale]

key.

✔

Obtain service from Keysight Technologies, if necessary.

If the trace display is unusual or unexpected

✔

Check that the Horizontal time/division setting is correct for the expected

frequency range of the input signals.

✔

The sampling speed of the oscilloscope depends on the time/division setting. It

may be that when time/division is set to slower speeds, the oscilloscope is

sampling too slowly to capture all of the transitions on the waveform. Use peak

detect mode.

Содержание InfiniiVision 2000























































































Результаты поиска

Содержание InfiniiVision 2000

Отзывы:

Похожие инструкции для InfiniiVision 2000

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 2000, Руководство по обслуживанию

Результаты поиска

Содержание InfiniiVision 2000

Отзывы:

Похожие инструкции для InfiniiVision 2000

Бренды по названию

Популярные бренды