Keysight Technologies InfiniiVision 2000 Скачать руководство пользователя страница 25

Страница: 25 / 86

Testing Performance

2000/3000 X-Series Oscilloscopes Service Guide

Turn on the test equipment and the oscilloscope. Let them warm up for 30

minutes before starting the test.

Set up the precision source.

Set the precision source to provide a DC offset voltage at the Channel 1

output.

Note: Set the Low Force terminal of the Precision Source to its "Floating"

state to prevent offset error caused by ground loop current from the

Precision Source ground to the DUT ground.

Use the multimeter to monitor the precision source DC output voltage.

Use the 8-by-2 test connector and the BNC cable assembly to connect digital

channels D0-D7 to one side of the BNC Tee. Then connect the D0-D7 ground

lead to the ground side of the 8-by-2 connector. See

Figure 2

Table 4

Equipment Required to Test Digital Channel Threshold Accuracy

Equipment

Critical Specifications

Recommended Model/Part

Digital Multimeter

0.1 mV resolution, 0.005% accuracy

Keysight 34401A/34461A

Precision Source

DC voltage of -5.5 V to 5.5 V, 10 mV resolution

Keysight B2912A/B2962A

Adapter (qty 2)

BNC(f) to banana (m)

Keysight 1251-2277

BNC Tee

BNC Tee (m) (f) (f)

Keysight 1250-0781 or Pomona 3285

BNC Cable

BNC - BNC, 48” length

Keysight 8120-1840

BNC Test Connector,

8-by-2

User-built (See

page 21

)

Probe Cable

No substitute

16-chanel: Keysight N6450-60001 or

N2756-60001

8-channel: Keysight N6459-60001 or

N2755-60001

Содержание InfiniiVision 2000























































































Результаты поиска

Содержание InfiniiVision 2000

Отзывы:

Похожие инструкции для InfiniiVision 2000

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 2000, Руководство по обслуживанию

Результаты поиска

Содержание InfiniiVision 2000

Отзывы:

Похожие инструкции для InfiniiVision 2000

Бренды по названию

Популярные бренды