Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 363

Страница: 363 / 378

UART/RS232 Triggering and Serial Decode

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

363

UART/RS232 Triggering

To set up the oscilloscope to capture UART/RS-232 signals, see

"Setup for

UART/RS232 Signals"

on page 361.

To trigger on a UART (Universal Asynchronous Receiver/Transmitter) signal

connect the oscilloscope to the Rx and Tx lines and set up a trigger condition.

RS232 (Recommended Standard 232) is one example of a UART protocol.

Press

[Trigger]

In the Trigger Menu, press the

Trigger

softkey; then, turn the Entry knob to

select the serial slot (Serial 1) on which the UART/RS232 signals are being

decoded.

Press the

Trigger Setup

softkey to open the UART/RS232 Trigger Setup Menu.

Press the

Base

softkey to select Hex or ASCII as the base displayed on the Data

softkey in the UART/RS232 Trigger Setup Menu.

Note that the setting of this softkey does not affect the selected base of the

decode display.

Press the

Trigger

softkey and set up the desired trigger condition:

•

Rx Start Bit

— The oscilloscope triggers when a start bit occurs on Rx.

•

Rx Stop Bit

— Triggers when a stop bit occurs on Rx. The trigger will occur on

the first stop bit. This is done automatically whether the device under test

uses 1, 1.5, or 2 stop bits. You do not need to specify the number of stop bits

used by the device Under test.

•

Rx Data

— Triggers on a data byte that you specify. For use when the device

under test data words are from 5 to 8 bits in length (no 9th (alert) bit).

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды