Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 324

Страница: 324 / 378

324

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Reference

Acknowledgements

Third-party software acknowledgements and licenses for these InfiniiVision

X-Series oscilloscopes are located at

www.keysight.com/find/2000X-3000X-Series-third-party-software

Product Markings and Regulatory Information

These symbols are used on the 2000/3000 X-Series oscilloscopes.

Symbol

Description

Caution, risk of electric shock

Caution, refer to accompanying documentation

The crossed out wheeled bin symbol indicates that separate collection for

waste electric and electronic equipment (WEEE) is required, as obligated

by the EU DIRECTIVE and other National legislation.
Please refer to

keysight.com/go/takeback

to understand your Trade

in options with Keysight in addition to product takeback instructions.

Indicates the time period during which no hazardous or toxic substance

elements are expected to leak or deteriorate during normal use. Forty

years is the expected useful life of the product.

The RCM mark is a registered trademark of the Australian

Communications and Media Authority.

The CE mark is a registered trademark of the European Community.
ICES / NMB-001 Cet appareil ISM est conforme a la norme NMB du

Canada. This is a marking to indicate product compliance with the

Industry Canadian Interference-Causing Equipment Standard (ICES-001).
This is also a symbol of an Industrial Scientific and Medical Group 1 Class

A product (CISPR 11, Clause 4).

The CSA mark is a registered trademark of the CSA International.

ICES/NMB-001

ISM GRP 1-A

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды