Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 283

Страница: 283 / 378

Utility Settings

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

283

The resultant string is displayed in the "Text =" line above the softkeys.

Press the

Wait

softkey; then, turn the Entry knob to select the number of

minutes to wait before the selected screen saver activates.

When you turn the Entry knob, the number of minutes is displayed on the

Wait

softkey. The default time is 180 minutes (3 hours).

Press the

Preview

softkey to preview the screen saver you have selected with the

Saver

softkey.

To view the normal display after the screen saver has started, press any key or

turn any knob.

To set AutoScale preferences

Press

[Utility] > Options > Preferences > AutoScale

In the AutoScale Preferences Menu, you can:

•

Press the

Fast Debug

softkey enable/disable this type of autoscale.

When fast debug is enabled, autoscale lets you make quick visual

comparisons to determine whether the signal being probed is a DC voltage,

ground, or an active AC signal.

Channel coupling is maintained to allow easy viewing of oscillating signals.

•

Press the

Channels

softkey and turn the Entry knob to specify the channels to

be autoscaled:

•

All Channels

— The next time you press

[AutoScale]

, all channels that meet

the requirements of AutoScale will be displayed.

•

Only Displayed Channels

— The next time you press

[AutoScale]

, only the

channels that are turned on will be examined for signal activity. This is

useful if you only want to view specific active channels after pressing

[AutoScale]

•

Press the

Acq Mode

softkey and turn the Entry knob to select whether the

acquisition mode should be preserved during autoscale:

•

Normal

— to make the oscilloscope switch to Normal acquisition mode

whenever the

[AutoScale]

key is pressed. This is the default mode.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды