Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 267

Страница: 267 / 378

Save/Recall (Setups, Screens, Data)

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

267

In the Save/Recall Menu, press

Default/Erase

In the Default Menu, press one of these softkeys:

•

Default Setup

— recalls the oscilloscope's default setup. This is the same as

pressing the front panel

[Default Setup]

key. See

"Recall the Default

Oscilloscope Setup"

on page 30.

Some user settings are not changed when recalling the default setup.

•

Factory Default

— recalls the oscilloscope's factory default settings.

You must confirm the recall because there are no user settings that are left

unchanged.

Performing a Secure Erase

Press the

[Save/Recall]

key.

In the Save/Recall Menu, press

Default/Erase

In the Default menu, press

Secure Erase

This performs a secure erase of all non-volatile memory in compliance with

National Industrial Security Program Operation Manual (NISPOM) Chapter 8

requirements.

You must confirm the secure erase, and the oscilloscope will reboot when

finished.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды